Plumbing Basics: What You Need for Bathtub Installation
Set Up An AppointmentListed here down the page you can get additional excellent expertise concerning Installing A Bathtub.
Setting up a tub isn't exactly rocket science, however it does need solid plumbing, woodworking, and in some cases, tiling skills. Changing an old tub with a new one is also a reasonably tough project. If the old bathtub is easily accessible, the task can relocate immediately; if you have to open a wall to get rid of the old tub as well as place the new bathtub, the job is much harder. In either instance, the task is within a residence handyman's abilities, although you will require a helper to move out the old bathtub and also set in the new one. Ensure you have actually qualified yourself for the job and also are comfortable trying it. As opposed to hiring a service provider to take control of a halfway-completed project, it is much better to think about utilizing one prior to you start. Possibilities are you may need a specialist plumber to make tube connections.
This write-up will assist you install a new bathtub in your restroom if you have actually currently gotten a brand-new tub as well as do not require to change the setup of your previous water pipes.
Your devices and also material list must consist of the following:
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installation, after that the first thing you should do is separate the supply of water. After doing so, switch on the faucets to drain pipes any water staying in the system. The procedure of removing the existing taps can be quite problematic due to the restricted accessibility that is frequently the case.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the taps. Have a fabric all set for the remaining water that will certainly originate from the pipes. As soon as the supply pipelines have been gotten rid of, use the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary faucets from turning during this process. When the faucets have been eliminated, the holes in the bath/basin will have to be cleaned up of any kind of old sealing substance.
Before going on to fit the new faucets, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will certainly require a plastic connector to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet and also the other end supplies a link to the current supply pipes.
If you need to fit a monobloc, then you will certainly require minimizing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the installing opening in the bath/basin ensuring that the washers remain in place between the faucet and also the sink. Protect the faucet in place with the manufacturer supplied backnut. As soon as the tap is safely in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with regular faucet connectors. The previous kind ought to be linked to the faucet ends first, tightening just by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Installing the Bathtub
Using both wooden boards under its feet, put the tub in the required setting. The wooden boards are valuable in evenly spreading the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto 4 small factors.
The following objective is to ensure that the tub is leveled all round. This can be accomplished by checking the level and adjusting the feet on the bathtub up until the spirit level checks out level.
To mount faucets, fit the bottom of the outermost flexible faucet connector to the proper supply pipeline by making a compression sign up with; after that do the same for the various other tap.
Turn on the water system and also examine all joints and also brand-new pipework for leaks and also tighten them if required. Fill up the bathtub as well as additionally check the overflow outlet as well as the typical electrical outlet for leaks.
Finally, deal with the bath paneling as defined in the manufacturer's user's manual. Tiling as well as securing around the bathtub should wait until the bath tub has been made use of at least when as this will certainly resolve it right into its final position.
Preparing for the Installation
First of all, the sustaining frame provided with the bathroom should be fitted (if needed) according to the manufacturer's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is essential to make certain that if the faucet comes with a plastic washer, it is fitted between the bath and the faucets. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the taps unit to avoid pressure on the bathtub.
Fit the versatile tap connectors to the bottom of both faucets utilizing 2 nuts and also olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you use every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom ought to currently prepare to be suited its last position.
Tiling Around the Bathtub
In the area where the bath fulfills the tile, it is essential to seal the joins with a silicone rubber caulking. This is important as the fitting can move sufficient to split an inflexible seal, causing the water to penetrate the wall surface in between the bathroom and also the tiling, bring about complications with dampness and also possible leaks to the ceiling below.
You can select from a selection of coloured sealers to assimilate your components and fittings. They are sold in tubes and cartridges, and can sealing gaps as much as a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill the bath tub with water before sealing, to allow for the movement experienced when the tub is in usage. The sealer can crack relatively very early if you do not take into account this activity before securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly available on the market. It is a good idea to fit the ceramic tiles utilizing water-resistant or waterproof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you enjoyed reading our piece on A Step-by-Step Guide to Installing a Bathtub. Thank you for taking a few minutes to read our piece of content. Enjoyed reading our piece of writing? Please share it. Let others discover it. Thanks a lot for your time. Please come by our site back soon.
Best decision? Call us.